‫Great, so we attach Cowley to our network physically.
‫Now we have to make the configurations to make Carly a part of Velan.
‫10.
‫So as you can see here, my colleague is not running at the moment.
‫I'll go to the switches console to configure the connection.
‫It'll be similar to configurations of the VPC.
‫Type conf T.
‫To enter the configured terminal mode.
‫And then into F1 one slash three to configure the interface fast Ethernet one slash three, which is
‫used for Collie.
‫We have seen these before, so I'll just go through it quickly, switch port mode access.
‫Switch Port Access within 10.
‫No, shut down.
‫Exit.
‫Exit again, go to the root and W are to write the configuration to make it persistent, OK, to check
‫the current situation of the interfaces we can now use show IP interface brief.
‫Here's the interface of Cali fast Ethernet one slash three.
‫It's supposed to be up is shown here.
‫However, if you stop the switch and started again, your interface is probably down for now.
‫As you can see here, my fast Ethernet one slash four interface is up, which is supposed to be down
‫because nothing is connected to it.
‫So I added another VM and removed it while I wasn't recording.
‫That's why it looks like this.
‫So let's restart the which.
‫What's expected at the end is your Cali port will be up and my F1 four port will be down.
‫So I click on Switch, select Stop and right click again and select Start.
‫Switches up.
‫Let's look at the interfaces again.
‫Open console, the switches initializing.
‫Show IP interface brief.
‫And as you see, fast, even at one three, the interface of my colleague is up is expected f one slash
‫four was up before the restart and it's down now and that's the expected result to.
‫So I suppose your college port was down before the restart, and it's up now, if not just go back and
‫do the steps again.
‫So now let's go to Carly and configure it, since we don't have a DHCP in our network, we have to assign
‫the IP addresses for the node of the network manually.
‫So right click on Colli and select Start and colleagues started, and it's initializing.
‫Log in with route user, my password is still to or.
‫OK, first, I want to check the network interface inside Colleen.
‫Well, the upper right corner, right click to the network icon, and if zero is selected, that's exactly
‫what I want.
‫Now, the double check.
‫I'll go to the network interface from VMware menu, and yep, there it is in custom mode, just as I
‫wanted.
‫Now, as I mentioned before, we have to assign the IP address, subnet mask gateway, et cetera, manually.
‫So open a terminal and we'll use ifconfig to configure is zero.
‫All right, so if config the interface either zero, the IP address for Carly, I'll choose one nine
‫two two eight one six eight one zero two three.
‫Some netmask 255.255.255.0 and hit enter now to check the network, let's ping the router first.
‫It was one nine two two eight one six eight one zero one and yep, there it is.
‫We got the reply packets and that's a good thing.
‫And now you can use Control C to quit the ping command.
‫So let's bring another device in the same network.
‫The BBC, its IP was turned up to excellent, right?
‫So now just to triple check.
‫Let me go to the VPC and ping colli from there.
‫The IP of Carly is 10.3 perfect, and we've got the reply package to prove it.
‫Let's go for a quadruple check.
‫OK, so I'll go to the router's console and ping Carly.
‫The success rate is 100 percent, so as you see, the ping result is given in a different format and
‫the router and then the result is again just as we expected.