Hello and welcome to the simulation, and I'm just going to connect E.S.P first to board with Arduino.
We are going to use Fritzing Software.
It's a very well known software for creating circuit design, and it's a very good software for showing
the wiring layout for any electronic circuit.
So let's go to breadboard mode here.
Now we need to add Arduino board so you can go here and select arguing.
All this is the board.
Now, the next step will be.
Getting a split to board.
This is it here we have our yes, we have to ball.
Now we need a logic level shifter.
You can buy logic and you will get tons of results.
Qualitest.
OK, now we have, as you can see, a little convertor, we have this one.
And we have others as well.
But this one will be enough for us now.
To start connecting, let's sort of this by 90 degrees right now, we need to connect the three point
three volt from the E.S.P board, which is the sport to our logic level shifter.
So this is the three point three ball and we need to connect it to.
The low voltage bin, this one, Elvie.
And let's make it right now, the next step is connecting the five miles from our old Linebaugh to the
HIV or high level the spin.
So let's try this one here.
That's it.
No.
We need to connect the ground from our Arduino with the logic of a converter with a USB port so the
ground from here must be connected to the ground of the level.
Touch on the ground from here must be connected to the ground from our level shifter.
Now, let's change the color to black here.
Around here.
List that this plan.
OK, now.
Moving on, let's approach this.
Now, we have connected the power underground and everything is connected correctly.
We need to connect the serial communication wires and the first step is going to our Arduino on board.
And since we have initialized and according to PIN number two and three for the connection, we need
to connect that up in number three, which is the spin to our logical level converter.
And we need to make sure that we are choosing ATX, H.V. or high voltage.
So you need to go to the X.
HIV, and as you can see, we have more than one T X. This is T to its V, we need to X S.V., which
is dispo.
No.
Let's move it up here.
OK.
Now, let's show the color to yellow.
Now we have connected.
Number three has now been called, we have said number two and 340, Xander X.
Now the artists from here, which has been number three, is connected to the T x h.
We make sure that you are choosing the right band.
Then you need to connect the R x D zero from your ISP board.
So as you can see here, we have Artex zero zero.
So now let's go and grab the ah x pen and connect to the T X LV.
Here.
OK, now, as you can see, this is the three X.
LV, and we have the Arduino pin connected to 3x HIV, and this is basically the conversion it will
take for Arduino, convert it and send it to various people without burning the ball.
And this is the main goal from the converter.
Now, you can see the schematic by clicking here, as you can see.
These are the two boards.
You can move these balls like this and we can rotate, as you can see, by 90 degree guaranteed by one
hundred eighty degree.
OK, now the ground is connected between these two balls.
And as you can see, we have this spin optics and the as people connected to the T SLV PIN number six,
and we have been different from our Arduino connected to that actually.
And we have actually high voltage connected to the five volt and the low voltage.
All the Elvie connected to the three points revolved.
That's it.
This is our connection, make sure that you have everything connected, that we don't mix things up,
try to double check your connection before moving forward and connecting your part, because if you
have connected any wire and along with it might damage your bond.
Double check before moving on.
Thanks for sharing this lesson.
If you have any questions regarding anything of this connection, you can ask on the airport.
This is Ashenoff from educational engineering team.