1
00:00:00,210 --> 00:00:05,250
Hello and welcome to this annual list one which I will teach you how to measure current measuring and

2
00:00:05,250 --> 00:00:12,390
current is uh a little bit harder than measuring voltage because there is uh two ranges in the amber

3
00:00:12,510 --> 00:00:21,060
and the umber range so you don't want to confuse these two because this might damage your digital multimeter.

4
00:00:21,660 --> 00:00:28,290
So when you are measuring if you are measuring small you use this one if you are not sure use this one

5
00:00:28,670 --> 00:00:30,190
because it can measure up to arm.

6
00:00:30,510 --> 00:00:38,210
But if you are higher than an arm you shouldn't use this one you should buy a watch that has such specifications.

7
00:00:38,370 --> 00:00:44,990
Now in order to make that count you need to move the dial here as you can see we have from 20 million

8
00:00:45,030 --> 00:00:50,890
to 10 AC and from 20 million to 10 DC.

9
00:00:51,060 --> 00:01:02,590
So this start by stating how to measure car in order to measure confidence circuits you need to do short.

10
00:01:02,880 --> 00:01:05,010
So you need to cut the circuit.

11
00:01:05,100 --> 00:01:16,800
Let's say that we have a nine volt battery was terminal and we have a lead resistor and LEDs and around

12
00:01:18,300 --> 00:01:25,240
this lead will turn on if we want to measure how much current is withdrawn in this circuit.

13
00:01:25,270 --> 00:01:27,510
We need to break this circuit.

14
00:01:27,750 --> 00:01:29,530
So now it would become like this

15
00:01:34,460 --> 00:01:35,740
and this.

16
00:01:36,060 --> 00:01:40,230
These are the two blobs of the digital multimeter.

17
00:01:40,230 --> 00:01:45,760
We must add them in series with the circuit so that we can measure the current.

18
00:01:45,780 --> 00:01:53,940
Now the same thing apply to as you can see this is a this evolved the same thing apply for AC if you

19
00:01:53,940 --> 00:02:02,040
want to measure current that goes through let's say at 100 to 120 volt AC plug.

20
00:02:02,430 --> 00:02:07,380
Let's say that this is the AC plug you need to go to Little multimeter.

21
00:02:07,380 --> 00:02:11,670
Then let's say that this is a light bulb.

22
00:02:11,670 --> 00:02:13,950
This is the line and this is done.

23
00:02:14,190 --> 00:02:21,750
The neutron will be connected directly while the line all must go through the digital multimeter using

24
00:02:21,750 --> 00:02:22,740
these two blobs.

25
00:02:22,890 --> 00:02:36,380
In order for four to measure this that lamp consumes I will show you how to do it for the D.C. Circuit.

26
00:02:36,450 --> 00:02:38,460
And the same thing applies for the AC circuit.

27
00:02:38,460 --> 00:02:40,010
You need to cut the circuit.

28
00:02:40,150 --> 00:02:44,010
Cut the way out and let it pass through that digital multimeter.

29
00:02:44,010 --> 00:02:50,500
Then you can simply see the results on the icy display from the watch.

30
00:02:50,500 --> 00:02:53,200
Now let's do this in action.

31
00:02:53,310 --> 00:02:58,720
I want to enjoy this Volt saw last fall while the children's metal cell door.

32
00:02:58,830 --> 00:03:03,040
Let's move to the DC range.

33
00:03:03,770 --> 00:03:06,680
Okay I will wouldn't let my job small.

34
00:03:06,740 --> 00:03:12,250
So I will go to the DC 200 the um uh.

35
00:03:12,260 --> 00:03:16,280
Now I will place the props the chrome on the chrome.

36
00:03:16,880 --> 00:03:21,910
And this one that the arm because I know I will be resigning from the million range.

37
00:03:22,170 --> 00:03:31,890
That said on that display and I will take them adjournment for a very simple uh circuit.

38
00:03:32,060 --> 00:03:36,280
I have it here as you can see we have a lid and that is a store.

39
00:03:36,380 --> 00:03:43,910
As I thought earlier uh in order for this to turn on you must connect it like this.

40
00:03:43,910 --> 00:03:49,610
The uh positive terminal 2 that is a store and the negative terminal the lid to the ground.

41
00:03:49,610 --> 00:03:54,480
And as you can see it's on I need to cut the circuit so I will do the same.

42
00:03:54,650 --> 00:04:01,620
I'll connect uh the negative turn round to this but the most optimal I would permit to throw this uh

43
00:04:01,760 --> 00:04:05,780
device or throw the props of this multimeter.

44
00:04:06,410 --> 00:04:20,300
So let me just talk it up here as you can see now I have this blob on this prop I will connect the negative

45
00:04:21,290 --> 00:04:27,380
to the battery and connect the other probe to the distal multimeter.