Hello.
Welcome to the world of Computer-Aided Design.
It sort of goes into this session.
You're going to learn about the principles of dimensioning guest entities and solid SolidWorks.
After drawing sketches and adding relations.
Most important step in creating a design is damaged and votes being a parametric software.
The MTD on dimensioning is driven by the specified value, irrespective of the original size.
Therefore, when you apply.
And what if the dimensions of an entity, it is forced to change its size in accordance with the specified
damage that can damage should any kind of entity?
By using this smy dimension too.
If you use this small damage to the back of dimension to be applied will depend on the bank of NTPC.
For example, if you notice what I in to and then select a line signets can see automatically a linear
dimension gets attached to the cluster.
If you select an incline line and vertical line or horizontal dimension will be attached to the cause.
Similarly, if you select a circle, diameter dimension will be attached to the course.
If I select an OK radius, value will be attached to the cost.
However, if you want to play a particular type of dimension and choose the type of tool from this small
damage and play out.
Let us apply this one dimension to this line, Cygne.
So I click on this as damage tool and then I'll select this line.
He can see and I mentioned value is attached to the cursor and click here to place the damage as I click
on the screen to please the damage.
The modified out of books is invoked can modify the default damage in value by using the spinner like
this.
By entering a new value in this edit box, if you make it too tough.
And see, the length of the line segment has increased to 2000 double click on this damage in value
again to invoke that.
What if I dunno box.
You can also drag the tummy.
I didn't feel the spinner.
Here's the tummy.
To increase.
Or decrease the damage in value.
If you drag the tumble to a strike, the damage in value will be increased.
If you drag the tumble to its left, the damage in value will be decreased.
Also, some items are available here in this modified out of box.
The first one is seen the current value and exit the dialog box.
This button is used to accept the current value and a certain articles.
Second button is restored to the original value and accept the dollar.
And this button is used to restore the last damaged value applied to sketch and then set the next button.
Is region rates the model with the current value?
Let me change this value to any 800.
Now I click on this region, draped the model with current value, but you can see a preview of the
geometry of the sketch with the modified damage in value is displayed next Putnis.
Give us a sense of the damage.
This photo is used to flip the damaging value of an entity.
This button will be available in the modified out of box and the selector dimension is a linear damage.
Let me click on it can see the damage in value got flipped in other directions instead of twenty eight
hundred value, minus twenty eight hundred is to.
Next Putnis three six spin increments value.
This button is used to modify the incremental value of the spinner.
If you choose this button, inclement box is displayed.
Enter and implement value in this title box.
Suppose I want to dimensioned values to be incremented by a value of twenty units.
So I type 20.
And then at the center, if I tried to change the in value using the spinner, you can see that I mentioned
value will change in addition, subtraction of 20 units each.
Who said four zero seven two zero?
Seven hundred tried to increase this value.
Seven to zero, again, two seven four zero.
So an increment or decrement of 20 units is applied to this damage.
Last button is Mark Dimensioned to be imported into attrite, this button is chosen to make sure that
the selected dimensioned is selected as a model annotation in the drawing views.
It does, but it is not chosen selected damage and will not be generated in the drafting in the.
After modifying the damage in value, click on the save the current value and exit the data and then
click on this title button and press the escape key on your keyboard to get out of this smart dimension
to.
So these are the basic principles of dimensioning inside.
Thank you for watching this video.